Brick Paver Installation & Edging



Staging of material

The majority of paver jobs will vary depending upon access, website conditions, project size and obviously, the weather. These scenarios can have an overall influence on your project from a timing stand point. Mindful consideration must be taken to identify the time to begin the paver installation. Always try to decrease or avoid any traffic on the ready areas.

The supervisor or project supervisor should constantly have the products (sand/ pavers) distributed around the task site for efficient and easy installations. Paver pallets/bundles need to be placed in a way not to interfere with the paver installation. The appropriate pallet/bundle placement can make the real project installation much easier and quicker by reducing the general labor of managing the material.

Brick paver patterns

Pavers can be put in many different patterns depending on their shape. Each paver shape will usually have several various hatch patterns that are provided by the producer.

Professionals require to take into consideration the traffic weight loads on their paver jobs. In a lot of applications worldwide, it has been shown that pavers laid in a herringbone pattern have actually performed sufficiently.

Pavers that are 60 mm (2 - 3/8 in) density are suitable for pedestrian applications. Pavers that are going to be used in commercial or commercial applications should be 80 mm (3 - 1/8 in) in thickness.

Reference/starting point for brick paver installation

There are a variety of conditions that figure out the starting point of a paver job.

When beginning to set up pavers it is best to snap a true straight chalk line on the surface of the bedding sand or pull a true straight string line above the surface area of the bed linen sand at the ended up elevation of the pavers This will help as a guide for preserving straight joint lines and will likewise permit the installer to make adjustments in the alignment of the pavers.

Buildings and concrete suppressing are usually not straight and need to not be used for establishing straight joint lines. Using string lines is vital to figure out the true straightness of the edge also. As the paver installation progresses, the string lines will assist minimize the need for small trim pieces.

These will maintain a minimum joint width and enable the bedding and jointing sand to go into in between each paver. Pavers with spacer bars are normally not laid in snug versus each other given that a string line will provide consistent joint spacing.

Installation of brick pavers.

One of the most widely used methods for the installation of pavers is hand installation of each paver. It is best to install a single row of pavers along one of the real straight lines that you have actually pulled or above the bed linen sand. The finest approach is to place a paver versus another one and let it move down into the bed linen sand.

When setting up pavers on a steep grade, they ought to be installed at the base of the grade going uphill. This will prevent the pavers from creeping as they are being laid.

The best way for installing pavers on large tasks is to install them mechanically. There are a couple products a specialist must think about prior to installing pavers mechanically:

1.) Mechanical installers are just efficient in setting up pavers in specific patterns.

2.) The contractor must make sure that the maker can production and bundling pavers in the preferred pattern on the pallets for easy mechanical installation.

Poor color blending could result in an irregular looking installation. The majority of producers are constant with color mixing on each package of pavers, but it is the contractor's responsibility to make sure appropriate blending in the field.

Cutting procedures for brick pavers.

Specialists normally have 2 ways of cutting pavers. Pavers are cut either by 1). A double bladed guillotine or by 2). A gas powered cut off saw or brick saw which is equipped with a diamond blade. The diamond blade cut-off saw or brick saw will supply a much cleaner and more precise cut. Many brick saws will have a hose accessory on them which will enable the operator to cut the pavers wet. When cutting pavers damp, it will help minimize dust and will lengthen the diamond blades life. The operator of the brick saw must always cut the pavers away from the surface area of the paver field when cutting wet, due to the fact that the pavers will develop a slurry that will stain the paver surface area. Pavers that are cut should not fit tight, adequate spacing should be readily available for jointing sand.

The brick saw operator ought to always use the appropriate defense that is needed for operating a saw, such as eye, ear, breathing and hand protection ).

Edging types

Edge restraints play a significant function in the overall success of an interlocking pavement installation Edging restraints remove lateral movement of the pavers and hold the pavers securely together. Particularly at the external boundary of the paver application, without an edging restraint, your job is ensured to fail with time.

Normally produced edge restraints are the most commonly utilized by contractors. Produced edging restraints can range from, plastic edging, steel and aluminum, woods or precast concrete and stone.

Edging installation.

When installing your edge restraint, it should rest straight on top of the compacted gravel base. The compressed gravel base course should extend a minimum of 6in beyond the border of the pavers This will provide a correct foundation upon which the edging restraint can sit. Made edging (i.E. Plastic, steel or aluminum) ought to be strongly anchored into the compacted gravel base( contact the manufacturer's literature for the advised spacing of the spikes). There are some edging restraints that will extend deeper into the gravel base or beyond the base course (i.E. Timbers or poured-in-place curbs ). Edging restraints should never ever be placed directly on top of the bed linen sand. This could lead to the migration of the bedding sand and ultimate lateral motion of the pavers. If there is a possibility of losing bedding sand in between the pavers and the edge restraint, then geo textile fabric is suggested. When a space in between the pavers and the edging exceeds 3/8" (10mm), then the area should be filled with cut pavers. All edging applications ought to be properly back filled after they are installed to assist provide extra stability.

Compaction of brick pavers.

After installation, the pavers have to be compacted. The entire area that is to be compressed need to be swept clean of any foreign items and particles that can cause scratching Tree Service Del Ray Beach or scuffing on the surface of the pavers.

In addition, it is crucial that the first compaction takes place prior to any jointing sand has been applied to the pavers. If jointing sand is used to the pavers prior to compaction takes place, this can cause a bridging problem and will not permit the joints to be entirely filled with jointing sand. This can also avoid the pavers from being properly set into the bedding sand.

When condensing the pavers, it is advised that you make a minimum of two passes in different directions throughout the pavers. This will permit the pavers to be properly set in the bedding sand and will require the bed linen sand up into the joints from the bottom of the pavers.

The compaction of the pavers is really critical to the final performance of the pavers. Failure to do appropriate compaction can lead to contortions and pavement failure over time.


Paver pallets/bundles ought to be put in a way not to interfere with the paver installation. One of the most extensively utilized methods for the installation of pavers is hand installation of each paver. The operator of the brick saw should always cut the pavers away from the surface of the paver field when cutting damp, due to the reality that the pavers will develop a slurry that will stain the paver surface area. Edging restraints eliminate lateral movement of the pavers and hold the pavers securely together. When a space between the pavers and the edging exceeds 3/8" (10mm), then the space ought to be filled with cut pavers.

Leave a Reply

Your email address will not be published. Required fields are marked *